Tennant 6550D Скачать руководство пользователя страница 86

Страница: 86 / 96

MAINTENANCE

6550D 330330 (5--01)

2. If the loading surface is not horizontal or is

higher than 380 mm (15 in) from the ground,

use a winch to load machine.

If the loading surface is horizontal AND is

380 mm (15 in) or less from the ground, the

machine may be driven onto the truck or

trailer.

3. To winch the machine onto the truck or

trailer, attach the winching chains in the

holes at the bottom of the rear bumper.

If the machine has the optional rear tie down

brackets, attach the winching chains to

them.

4. Turn the bypass valve 90

from the normal

position before winching the machine onto

the truck or trailer. See

PUSHING OR

TOWING THE MACHINE

section of this

manual. Make sure the machine is centered.

FOR SAFETY: When loading machine

onto truck or trailer, use winch. Do not

drive the machine onto the truck or

trailer unless the loading surface is

horizontal AND is 380 mm (15 in) or less

from the ground.

08151

Содержание 6550D

































































































Результаты поиска

Содержание 6550D

Отзывы:

Похожие инструкции для 6550D

Бренды по названию

Популярные бренды

Tennant 6550D, Руководство оператора

Результаты поиска

Содержание 6550D

Отзывы:

Похожие инструкции для 6550D

Бренды по названию

Популярные бренды