Tennant 6550D Скачать руководство пользователя страница 37

Страница: 37 / 96

OPERATION

6550D 330330 (9--02)

STARTING THE MACHINE

1. You must be in the operator’s seat with the

directional pedal in neutral, and your foot on

the brake pedal or with the parking brake

set.

For Safety: When starting machine,

keep foot on brake and directional pedal

in neutral.

2. Turn the ignition switch key all the way

counter-clockwise and hold it there for 15 to

60 seconds depending on the weather

conditions.

3. Turn the ignition switch key clockwise until

the engine starts.

NOTE: Do not operate the starter motor for more

than 10 seconds at a time or after the engine has

started. Allow the starter to cool between starting

attempts or damage to the starter motor may

occur.

4. Allow the engine and hydraulic system to

warm up three to five minutes.

WARNING: Engine emits toxic gases.

Severe respiratory damage or

asphyxiation can result. Provide

adequate ventilation. Consult with your

regulatory authorities for exposure

limits. Keep engine properly tuned.

07754

07805

07804

Содержание 6550D

































































































Результаты поиска

Содержание 6550D

Отзывы:

Похожие инструкции для 6550D

Бренды по названию

Популярные бренды

Tennant 6550D, Руководство оператора

Результаты поиска

Содержание 6550D

Отзывы:

Похожие инструкции для 6550D

Бренды по названию

Популярные бренды