Tennant 6550D Скачать руководство пользователя страница 66

Страница: 66 / 96

MAINTENANCE

6550D 330330 (5--98)

ENGINE

COOLING SYSTEM

Check the radiator core exterior for debris every

100 hours of operation. Blow or rinse all dust,

which may have collected on the radiator, in

through the grille and radiator fins, opposite the

direction of normal air flow. The grille and

hydraulic cooler open for easier cleaning. Be

careful not to bend the cooling fins when cleaning.

Clean thoroughly to prevent the fins becoming

encrusted with dust. Clean the radiator and cooler

only after the radiator has cooled to avoid

cracking.

FOR SAFETY: When servicing machine,

wear eye and ear protection when using

pressurized air or water.

Check the radiator coolant level every 100 hours

of operation. Use clean water mixed with a

permanent-type, ethylene glycol antifreeze to a

--34

C (--30

F) rating.

FOR SAFETY: When servicing machine,

avoid contact with hot engine coolant.

Check the radiator hoses and clamps every

200 hours of operation. Tighten the clamps if they

are loose. Replace the hoses and clamps if the

hoses are cracked, harden, or swollen.

Flush the radiator and the cooling system every

800 hours of operation, using a dependable

cleaning compound.

07809

07752

Содержание 6550D

































































































Результаты поиска

Содержание 6550D

Отзывы:

Похожие инструкции для 6550D

Бренды по названию

Популярные бренды

Tennant 6550D, Руководство оператора

Результаты поиска

Содержание 6550D

Отзывы:

Похожие инструкции для 6550D

Бренды по названию

Популярные бренды