Tennant 6550D Скачать руководство пользователя страница 88

Страница: 88 / 96

MAINTENANCE

6550D 330330 (5--01)

MACHINE JACKING

Empty the hopper before jacking the machine.

You can jack up the machine for service at the

designated locations. Use a hoist or jack that will

support the wieght of the machine. Always stop

the machine on a flat, level surface and block the

tires before jacking the machine up.

The front jacking locations are on the flat bottom

edge of the front of the machine frame next to the

front tires.

The rear jacking location is the middle flat bottom

edge of the rear bumper between the taillights.

FOR SAFETY: When servicing machine,

block machine tires before jacking

machine up.

FOR SAFETY: When servicing machine,

jack machine up at designated locations

only. Block machine up with jack

stands.

STORING MACHINE

Before storing the machine for an extended period

of time, the machine needs to be prepped to

lessen the chance of rust, sludge, and other

undesirable deposits from forming. Contact

TENNANT service personnel.

08029

08030

Содержание 6550D

































































































Результаты поиска

Содержание 6550D

Отзывы:

Похожие инструкции для 6550D

Бренды по названию

Популярные бренды

Tennant 6550D, Руководство оператора

Результаты поиска

Содержание 6550D

Отзывы:

Похожие инструкции для 6550D

Бренды по названию

Популярные бренды