Tennant 6550D Скачать руководство пользователя страница 73

Страница: 73 / 96

MAINTENANCE

6550D 330330 (9--02)

11. Check the shaker solenoid gap with the end

of the shipping tab. The gap should be the

same width as the tab. If it is not, loosen the

mounting screws, adjust the gap be

repositioning the shaker solenoid, then

tighten the screws.

12. Place the dust filter element assembly into

the hopper insert and reconnect the filter

shaker wire.

13. Center the dust filter cover over the element,

then push the cover back until the rear

vacuum fan seal is pressed against the

hopper insert.

14. Fasten the dust filter cover onto the element

with the retainer brackets, washers, and

knobs.

15. Close the hopper cover.

THERMO SENTRY

The Thermo Sentry

senses the temperature of

the air pulled up from the hopper. If there is a fire

in the hopper, the Thermo Sentry

stops the

vacuum fan and cuts off the air flow.

Reset the Thermo Sentry

by pushing in its reset

button.

Содержание 6550D

































































































Результаты поиска

Содержание 6550D

Отзывы:

Похожие инструкции для 6550D

Бренды по названию

Популярные бренды

Tennant 6550D, Руководство оператора

Результаты поиска

Содержание 6550D

Отзывы:

Похожие инструкции для 6550D

Бренды по названию

Популярные бренды