Tennant 6550D Скачать руководство пользователя страница 75

Страница: 75 / 96

MAINTENANCE

6550D 330330 (5--98)

TO REPLACE MAIN BRUSH

1. Stop the engine and set the machine parking

brake.

FOR SAFETY: Before leaving or

servicing machine; stop on level

surface, set parking brake, turn off

machine and remove key.

2. Raise the main brush.

3. Open the right side main brush access door.

4. Unlatch and remove the brush idler plate.

5. Grasp the main brush; pull it off the brush

drive plug and out of the main brush

compartment.

6. Put the new or rotated end-for-end main

brush on the floor next to the access door.

7. Slide the main brush onto the drive plug.

Rotate the brush until it engages the drive

plug, and push it all the way onto the plug.

8. Slide the main brush idler plate plug onto the

main brush.

9. Latch the idler plate onto the machine frame.

10. Close the right side main brush access door.

08016

08017

08018

Содержание 6550D

































































































Результаты поиска

Содержание 6550D

Отзывы:

Похожие инструкции для 6550D

Бренды по названию

Популярные бренды

Tennant 6550D, Руководство оператора

Результаты поиска

Содержание 6550D

Отзывы:

Похожие инструкции для 6550D

Бренды по названию

Популярные бренды