Tennant 6550D Скачать руководство пользователя страница 79

Страница: 79 / 96

MAINTENANCE

6550D 330330 (5--98)

TO REPLACE SIDE BRUSH

1. Empty the debris hopper.

2. Set the machine parking brake.

3. Stop the engine.

FOR SAFETY: Before leaving or

servicing machine; stop on level

surface, set parking brake, turn off

machine and remove key.

4. Raise the side brush.

5. Remove the side brush retaining pin from

the side brush drive shaft by pulling the pin

keeper off over the end of the pin.

6. Slide the side brush off the side brush drive

shaft.

NOTE: Remove the drive hub and put it on the

new brush if one is not installed.

7. Slide the new side brush onto the side brush

drive shaft.

8. Insert the side brush retaining pin through

the side brush hub and shaft.

9. Secure the pin by clipping the pin keeper

over the end of the pin.

10. Disengage the hopper support bar and lower

the hopper.

11. Adjust the side brush pattern with the side

brush down pressure knob.

SIDE BRUSH GUARD

Rotate the side brush guard 90

every 200 hours

of operation. Replace the brush guard after all

four sides have been used.

08019

08049

Содержание 6550D

































































































Результаты поиска

Содержание 6550D

Отзывы:

Похожие инструкции для 6550D

Бренды по названию

Популярные бренды

Tennant 6550D, Руководство оператора

Результаты поиска

Содержание 6550D

Отзывы:

Похожие инструкции для 6550D

Бренды по названию

Популярные бренды