Tennant 6550D Скачать руководство пользователя страница 6

Страница: 6 / 96

SAFETY PRECAUTIONS

6550D 330330 (9--02)

6. When servicing machine:

-- Avoid moving parts. Do not wear loose

jackets, shirts, or sleeves.

-- Block machine tires before jacking

machine up.

-- Jack machine up at designated

locations only. Block machine up with

jack stands.

-- Use hoist or jack that will support the

weight of the machine.

-- Wear eye and ear protection when

using pressurized air or water.

-- Disconnect battery connections before

working on machine.

-- Avoid contact with battery acid.

-- Avoid contact with hot engine coolant.

-- Allow engine to cool.

-- Keep flames and sparks away from

fuel system service area. Keep area

well ventilated.

-- Use cardboard to locate leaking

hydraulic fluid under pressure.

-- Use TENNANT supplied or approved

replacement parts.

7. When loading/unloading machine

onto/off truck or trailer:

-- Turn off machine.

-- Use winch. Do not drive the machine

onto/off the truck or trailer unless the

load height is 380 mm (15 in) or less

from the ground.

-- Use truck or trailer that will support

the weight of the machine.

-- Set parking brake after machine is

loaded.

-- Block machine tires.

-- Tie machine down to truck or trailer.

Содержание 6550D

































































































Результаты поиска

Содержание 6550D

Отзывы:

Похожие инструкции для 6550D

Бренды по названию

Популярные бренды

Tennant 6550D, Руководство оператора

Результаты поиска

Содержание 6550D

Отзывы:

Похожие инструкции для 6550D

Бренды по названию

Популярные бренды