Teledyne T3EL15030 P Series Скачать руководство пользователя страница 17

Страница: 17 / 90

Local/Remote Operation Mode

The T3EL15030xP Programmable Electronic load provides two operation

modes: Local and Remote.

Local Operation Mode

After you power on the instrument, it will be in Local operation mode by default.

In Local operation mode, all the keys on the front panel are available for use.

Remote Operation Mode

In the Remote operation mode, you can send programming commands from a

controller (computer) via any one of the interfaces (GPIB, USB, RS232, or LAN).

In Remote operation mode, all the keys (except the Shift key plus the Display

key) will be disabled. This is known as “local lock out”. When locked, the

instrument front panel is disabled and the

load can only be controlled via

programming commands. To return to the local operation mode, press the Shift

key plus the Display key on the front panel.

Содержание T3EL15030 P Series



























































































Результаты поиска

Содержание T3EL15030 P Series

Отзывы:

Похожие инструкции для T3EL15030 P Series

Бренды по названию

Популярные бренды

Teledyne T3EL15030 P Series, Руководство пользователя

Результаты поиска

Содержание T3EL15030 P Series

Отзывы:

Похожие инструкции для T3EL15030 P Series

Бренды по названию

Популярные бренды