manualshive.com logo in svg

Teledyne ADFM Hot Tap, Инструкция по установке и эксплуатации, Страница: 93 / 116

Поделиться
Скачать
Teledyne ADFM Hot Tap Скачать руководство пользователя страница 93

ADFM® Flow Meter

Section 3  Maintenance and Troubleshooting

3-7

3.4.2 Troubleshooting Steps

The following procedures are intended to assist fault isolation in
cases where the Built-in-Test (BIT) cannot be executed (no
ADFM wakeup for example), or the BIT determines a problem
with the sensor.

Table 3-2 Troubleshooting During Operation

Symptom

Possible Problem(s)

Action

Message: “Transducer not found”

Sensor cable connector

Cabling between Motherboard and sensor 
connector of flow meter

Sensor or sensor cable

Refer to Section 3.4.4.

Message: “Recorder not found”

Recorder cable assembly

Recorder Assembly

Motherboard

Check recorder ribbon cable con-
nection to motherboard.

Replace recorder assembly.

Replace motherboard.

Message “No Command Prompt 
Found”

Incorrect port settings on computer

Adjust communication port settings 
on computer

Message “Cannot Open Port”

Ancillary Data VXDR, VDD1, and 
VDC are outside the range listed in 
section “Maintenance and Trouble-
shooting.”

Batteries or power supply

Motherboard

Replace batteries. Check power 
supply.

Replace motherboard.

Transmit Test Failure

Cabling between the sensor interface board 
and the ADFM rear panel sensor connec-
tor.

Connection between motherboard and sen-
sor interface board

Transducer cable or connectors

Motherboard

Verify all connections.

Replace motherboard.

Message: “Loop Test Failure.” An 
occasional loop test failure may be 
normal since this is a statistical 
test. The percentage of loop test 
failures should typically be less 
than 10%.

Transducer improperly connected, or dam-
aged

High interference source

Motherboard.

Eliminate interference source

a,

 or 

shield transducer environment.

Perform Field Test in WinADFM 
(refer to WinADFM software man-
ual).
The Correlation Magnitude at Lag 0 
should be 255; at Lag 7 it should be 
typically < 20. Also, the High Gain 
RSSI should be typically < 65.
Otherwise it may indicate a high 
source of interference.

Call the factory.

Any RAM Test failure

 Motherboard

Replace motherboard

Message: “Clock Interrupt failed”

a.  

It is recommended to record the values for Correlation Magnitude, High Gain RSSI, and the results of the 

transmit test for later reference

.

Содержание ADFM Hot Tap





















































































































Отзывы:

Нет отзывов