Teledyne ADFM Hot Tap Скачать руководство пользователя страница 14

Страница: 14 / 116

ADFM® Flow Meter
Section 1 Introduction

1-4

Table 1-2 Technical Specifications: Pro20 Open Channel Velocity Sensor

Sensor Body

Operating Temperature

23 to 95 °F (-5 to 35 °C)

Housing Material

Urethane

Static Pressure

250 psi nominal

Dimensions

8 x 3 x 1.5 inches (200 x 75 x 40 mm)

Weight

3.2 lbs (1.5 kg)

Beam Angles

1 & 3: 10°front-back; 20°to side
2 & 4: 20° front-back; 30° to side

Sensor Signal Cable

Operating Temperature

-40 to 125 °F (-40 to 52 °C)

Material

Polyethyline jacket

Length

50 ft (15 m) std.
100 ft (30 m) and 150 ft. (45 m) optional lengths available

Minimum Bend Radius

6 in (150 mm)

Outer Diameter

0.5 in (13 mm) nominal

Table 1-3 Technical Specifications: Hot Tap Insertion Velocity Sensor

Sensor Body

Operating Temperature

23 to 95 °F (-5 to 35 °C)

Housing

Plastic transducer assembly

on corrosion resistant stainless steel stem.

Rated NEMA 6P, IP68, defined as validated for submersion to 20 feet of depth
for 48 hours.

Static Pressure

200 psi nominal

Dimensions:

Sensor Head Diameter
Std stem length

Insertion

1.375 in. (35 mm)
2 feet (610 mm)
Fits 2 inch NPT (50 mm) standard tap

Weight (includes 50 ft. cable)

15 lbs (6.8 kg)

Beam Angles

1 & 3: 10°front-back; 20° to side
2 & 4: 20° front-back; 30° to side

Sensor Signal Cable

Operating Temperature

-40 to 140 °F (-40 to 60 °C)

Material

Polyethylene jacket

Length

50 ft (15 m) std; 100 ft (30 m) optional

Minimum Bend Radius

6 in (150 mm)

Outer Diameter

0.5 in (13 mm) nominal

Use safety installation kit (60-7007-030) for pressures above 100psi. Applications with pressures between 200 and 300
psi require a schedule 80 nipple (contact factory).

Custom stem lengths are available; call factory for more information.

Custom cable lengths are available; call factory for more information.

Содержание ADFM Hot Tap





















































































































Результаты поиска

Содержание ADFM Hot Tap

Отзывы:

Teledyne ADFM Hot Tap, Инструкция по установке и эксплуатации, Страница: 14 / 116

Результаты поиска

Содержание ADFM Hot Tap

Отзывы: