Teledyne ADFM Hot Tap Скачать руководство пользователя страница 7

Страница: 7 / 116

ADFM® Flow Meter

Table of Contents

1.5.1 Optional Interfacing Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8

Section 2 Setup and Installation

2.1 Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
2.2 Flowlink Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
2.3 WinADFM Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8

2.3.1 Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8
2.3.2 Connecting to the ADFM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-15

2.4 Preparing for Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-18

2.5 Sensor Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-25

2.5.1 General Cabling and Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-25

2.6 Pro20 Sensor Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-25

2.7 Hot Tap Sensor Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-39

2.7.1 Forced Depth and Scaling Constant (Hot Tap only) . . . . . . . . . . . . . . . . . 2-40

2.8 Insertion: Early Version HTI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2-41
2.9 Insertion: Current HTI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2-46
2.10 Applying Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2-51

2.10.1 Box Controller Batteries  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2-51
2.10.2 Box Controller On and Reset Switches . . . . . . . . . . . . . . . . . . . . . . . . . . .  2-53
2.10.3 Canister Controller Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2-54
2.10.4 Resetting the ADFM Canister   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2-55

2.11 Built In Tests (BITs) (Box Controller Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-56

2.11.1 Testing Interval  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2-56
2.11.2 Test Record . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2-56
2.11.3 Power-up BIT Procedure/Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2-56

2.12 Data Retrieval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-58
2.13 Flowlink . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-58

2.13.1 Viewing the Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-60

Содержание ADFM Hot Tap





















































































































Результаты поиска

Содержание ADFM Hot Tap

Отзывы:

Teledyne ADFM Hot Tap, Инструкция по установке и эксплуатации, Страница: 7 / 116

Результаты поиска

Содержание ADFM Hot Tap

Отзывы: