Teledyne ADFM Hot Tap Скачать руководство пользователя страница 110 | Manualshive

Страница: 110 / 116

Teledyne ADFM Hot Tap Скачать руководство пользователя страница 110

ADFM® Flow Meter
Appendix B Material Safety Data Sheets

B-10

Multisorb Technologies, Inc. Drican® (Indicating Silica Gel – Al Case ) July 21, 2008 Page 4 of 4

Section 14 – Transportation Information

U.S. Department of Transportation Shipping Name:

Not classified as a hazardous material. Not regulated.

Section 15 – Regulatory Information

(Not meant to be all inclusive - selected regulations represented)

TSCA Listed:

Yes (Ingredients)

DSL/NDSL (Canadian) Listed:

Yes (Ingredients)

OSHA:

See section 8 above.

NIOSH:

See section 8 above.
Animal tests conducted in 1976 - 1978. 18 month exposure at 15 mg / m

3

showed silica

deposition in respiratory macrophages and lymph nodes, minimum lung impairment, no silicosis.

ACGIH:

See section 8 above.

DOT:

Not classified as a hazardous material.

Section 16 – Other Information

HMIS – Hazardous Materials Identification System

HMIS Rating

Health
Flammability
Physical

1
0
0

The HMIS rating information is intended solely for the use of individuals trained in the use of the HMIS
rating system.

The NPCA specifically recommends that prepares of MSDSs should not place HMIS PPE designation
codes on the MSDSs or labels that leave the facility as it is not known the conditions under which the
customer will use this product.

This MSDS was prepared by: George E. Mckedy
Senior Applications Development Specialist
Multisorb Technologies, Inc.

This data and recommendations presented in this data sheet concerning the use of our product and the
materials contained therein are believed to be correct but does not purport to be all inclusive and shall be
used only as a guide. However, the customer should determine the suitability of such materials for his
purpose before adopting them on a commercial scale. Since the use of our products is beyond our control,
no guarantee, expressed or implied, is made and no responsibility assumed for the use of this material or
the results to be obtained therefrom. Information on this form is furnished for the purpose of compliance
with Government Health and Safety Regulations and shall not be used for any other purposes. Moreover,
the recommendations contained in this data sheet are not to be construed as a license to operate under, or a
recommendation to infringe, any existing patents, nor should they be confused with state, municipal or
insurance requirements, or with national safety codes.

«
...
108
109
110
111
112
...
»

Содержание ADFM Hot Tap





















































































































Отзывы:

Нет отзывов