Teledyne ADFM Hot Tap Скачать руководство пользователя страница 107 | Manualshive

Страница: 107 / 116

Teledyne ADFM Hot Tap Скачать руководство пользователя страница 107

ADFM® Flow Meter

Appendix B Material Safety Data Sheets

B-7

Multisorb Technologies, Inc. Drican® (Indicating Silica Gel – Al Case ) July 21, 2008 Page 1 of 4

MATERIAL SAFETY DATA SHEET

Effective Date

July 21, 2008

MSDS Number

M119

Section 1 – Product and Company Information

Product Name:

Drican® (Indicating Silica gel, Aluminum case)

Product Use:

Desiccant, absorbent

Grades:

Silica gel, indicating

Synonyms:

Amorphous silica gel, SiO

2

, silicon dioxide (amorphous)

Company;

Multisorb Technologies, Inc.

Street Address:

325 Harlem Road

City, State, Zip, Country:

Buffalo, NY 14224-1893 USA

Telephone Number:

(716) 824 8900 [USA] Monday - Friday (8:00 - 5:00 EDT)

Fax Number:

(716) 824 4091 [USA]

Website / E-Mail :

multisorb.com

Section 2 – Hazard Identification

Emergency Overview:

An aluminum case containing a clear blue granular material that poses little or no
immediate hazard. The case and the contents of the case are not combustible.

Potential Health Effects:
Eyes:

None

Skin:

None

Ingestion:

Ingestion is very unlikely but if ingested get medical attention.

Inhalation:

None

Medical Effects Generally Aggravated by Exposure:

None

Chronic Effects/Carcinogenity:

None

Section 3 – Composition / Information on Ingredients

Component Name

CAS Number

% by Weight

Synthetic amorphous silica gel (SiO

2

)

112926-00-8

80 - 90

Cobalt chloride

7646-79-9

.5

Aluminum

7429-90-5

10 - 20

While this material is not classified as hazardous under OSHA regulations, this MSDS contains valuable
information critical to the safe handling and proper use of this product. This MSDS should be retained and
available for employees and other users of this product.

Section 4 – First Aid Measures

Eyes:

Rinse the eyes well with water while lifting the eye lids. If irritation persists, consult a
physician.

Skin:

Wash affected area with soap and water.

Ingestion:

Ingestion is unlikely but if ingested get medical attention.

Inhalation:

Remove the affected person to fresh air and get medical attention if necessary.

Notes to Physician:

Not applicable

«
...
105
106
107
108
109
...
»

Содержание ADFM Hot Tap





















































































































Отзывы:

Нет отзывов