Teledyne ADFM Hot Tap Скачать руководство пользователя страница 59 | Manualshive

Страница: 59 / 116

Teledyne ADFM Hot Tap Скачать руководство пользователя страница 59

ADFM® Flow Meter

Section 2 Setup and Installation

2-39

2.7 Hot Tap Sensor

Installation

Recent changes have been made to the design of the Hot Tap
Insertion (HTI) sensor. The two versions have slightly different
dimensions and hardware. Operation is exactly the same for
both.

The two versions are most distinguishable from one another by
the appearance of the box at the head of the shaft. See
Figure 2-42, below. If your sensor has the smaller, metal box on
the left, follow the instructions in Section 2.8

Insertion: Early

. If your sensor has the larger, molded box on the

right, follow the instructions in Section 2.9

Insertion: Current

Figure 2-42 Early and current versions of the HTI sensor

WARNING

Never loosen any hardware on the Hot Tap sensor when the

pipe is pressurized. Pressure within the pipe can force the
shaft to come out of the pipe, causing grave injury to
anyone nearby.

Early HTI

Current HTI

WARNING

«
...
57
58
59
60
61
...
»

Содержание ADFM Hot Tap





















































































































Отзывы:

Нет отзывов