Teledyne ADFM Hot Tap Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 116

Teledyne ADFM Hot Tap Скачать руководство пользователя страница 3

Foreword

This instruction manual is designed to help you gain a thorough understanding of the operation of
the equipment. Teledyne Isco recommends that you read this manual completely before placing the
equipment in service.

Although Teledyne Isco designs reliability into all equipment, there is always the possibility of a
malfunction. This manual may help in diagnosing and repairing the malfunction.

If a problem persists, call or e-mail the Teledyne Isco Technical Service Department for assistance.
Simple difficulties can often be diagnosed over the phone.

If it is necessary to return the equipment to the factory for service, please follow the shipping
instructions provided by the Customer Service Department, including the use of the

Return

Authorization Number

specified.

Be sure to include a note describing the malfunction.

This

will aid in the prompt repair and return of the equipment.

Teledyne Isco welcomes suggestions that would improve the information presented in this manual
or enhance the operation of the equipment itself.

Teledyne Isco is continually improving its products and reserves the right to change product
specifications, replacement parts, schematics, and instructions without notice.

Contact Information

Customer Service

Phone:

(800) 228-4373

(USA, Canada, Mexico)

(402) 464-0231

(Outside North America)

Fax:

(402) 465-3022

Email:

[email protected]

Technical Support

Phone:

Toll Free (866) 298-6174

(Samplers and Flow Meters)

Toll Free (800) 775-2965

(Syringe Pumps and Liquid Chromatography)

Email:

[email protected]

Return equipment to:

4700 Superior Street, Lincoln, NE 68504-1398

Other Correspondence

Mail to:

P.O. Box 82531, Lincoln, NE 68501-2531

Email:

[email protected]

Revised

January

2020

«
1
2
3
4
5
...
»

Содержание ADFM Hot Tap





















































































































Отзывы:

Нет отзывов