Teledyne ADFM Hot Tap Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 116

Teledyne ADFM Hot Tap Скачать руководство пользователя страница 12

ADFM® Flow Meter
Section 1 Introduction

1-2

1.2 Initial Inspection

Upon receipt, inspect the shipping container for any damage. If
the shipping container or packing material shows signs of
damage, it should be retained until the contents have been
inspected for completeness and the system has been checked
both mechanically and electrically. If the contents are incomplete
or damaged, or if the system indicates a failure in some com-
ponent during initial testing, notify Teledyne Isco as soon as pos-
sible, and notify the carrier regarding any damage to the
shipping container and packing material.

Contact Information

Technical assistance for the ADFM flow meter can be obtained
from:

Teledyne Isco

4700 Superior St.
Lincoln NE 68504

Phone: (866) 298-6174 or (402) 464-0231
Fax: (402) 465-3022
E-mail: [email protected]

1.3 Technical

Specifications

The following tables provide technical specifications for the
ADFM box and cylindrical electronics controllers, and for the
Pro20 open channel and Hot Tap Insertion velocity sensors.

Table 1-1 Technical Specifications: ADFM Controller

Physical

Electronics Unit Enclosures

Wall or console-mounted box, or cylindrical canister

Operating Temperature

-15 to 125 °F (-26 to 52 °C)

Storage Temperature

-65 to 160 °F (-54 to 71 °C)

Packaging

Box
Canister

NEMA 4X (IP66)
NEMA 6P (IP68)

Dimensions

Box
Canister

17.5 x 14.8 x 6.7 in. (445 x 375 x 170 mm)
28.5 x 10 in. (724 x 254 mm)

Weight

Box
Canister

24 lbs (11 kg)
36 lbs (16 kg)

Measurement Performance

Flow

Accuracy

2% of reading in typical conditions

Velocity

Maximum Velocity

±30.0 ft/s (± 9m/s)

Velocity Bin Size

2 to 12 inches (50 to 3000 mm) - user selectable

«
...
10
11
12
13
14
...
»

Содержание ADFM Hot Tap





















































































































Отзывы:

Нет отзывов