Teledyne ADFM Hot Tap Скачать руководство пользователя страница 108

Страница: 108 / 116

ADFM® Flow Meter
Appendix B Material Safety Data Sheets

B-8

Multisorb Technologies, Inc. Drican® (Indicating Silica Gel – Al Case ) July 21, 2008 Page 2 of 4

Section 5 – Fire Fighting Measures

Flammable Properties:

Not flammable

Flash Point:

Not applicable

Method:

Not applicable

Flammable Limits:

Not flammable

Lower Flammability Limit:

Not applicable

Upper Flammability Limit:

Not applicable

Autoignition Temperature:

Not applicable

Hazardous Combustion Products:

Not applicable

Extinguishing Media:

Use extinguishing media that is appropriate for the surrounding fire. The silica gel
and the aluminum case are not combustible.

Fire Fighting Instructions:

The silica gel and the aluminum case are not combustible.

Unusual Fire and Explosion Hazards:

None

Section 6 – Accidental Release Measures

Spill:

Sweep or vacuum up and place the spilled material in a waste disposal container. Avoid raising dust.

Wash with soap and water after handling.

Section 7 – Handling and Storage

Handling:

Avoid raising dust and minimize the contact between worker and the material. Practice
good hygienic work practices.

Storage:

Store in a cool, dry location. Keep in sealed containers away from moisture. The silica gel
will readily adsorb moisture.

Section 8 – Exposure Controls/Personal Protection

Engineering Controls:

Not required.

Respiratory Protection:

Not required.

Skin Protection:

Not required.

Eye Protection:

Not required.

Exposure Limits

Component Name

OSHA

PEL

ACGIH

TLV

Other Recommended Limits

Silica gel

Cobalt chloride

Aluminum

TWA 20 mppcf

(80 mg / m

% SiO

)

.1 mg / m

(cobalt metal dust & fume)

TWA 15 mg / m

(total

dust)

TWA 5 mg / m

(respirable fraction)

Not applicable

TWA .02 mg / m

(as cobalt)

1 mg / m

(respirable

fraction of

aerosol)

NIOSH REL

TWA 6 mg / m

IDLH 3000 mg / m

NIOSH REL

TWA .05 mg / m

(Cobalt metal dust & fume as cobalt)

IDLH 20 mg / m

(as metal dust & fume as cobalt)

NIOSH REL TWA

10 mg / m

(total dust)

TWA 5 mg / m

(respirable fraction)

Содержание ADFM Hot Tap





















































































































Результаты поиска

Содержание ADFM Hot Tap

Отзывы:

Teledyne ADFM Hot Tap, Инструкция по установке и эксплуатации, Страница: 108 / 116

Результаты поиска

Содержание ADFM Hot Tap

Отзывы: