tecan Columbus Washer Скачать руководство пользователя страница 5

Страница: 5 / 82

Table of Contents

Safety

1.1

Instrument Safety............................................................................. 1-1

2. General

2.1 Introduction ...................................................................................... 2-1
2.2

Instrument Specifications ............................................................... 2-2

2.3

Instrument Description.................................................................... 2-4

2.3.1

Rear Panel Connections .................................................................... 2-4

2.3.2

Connection Diagram .......................................................................... 2-5

2.3.3

Instrument Options............................................................................. 2-6

2.3.4

Liquid System Diagram...................................................................... 2-8

2.4

Instrument Software Features ........................................................ 2-9

2.4.1

Software Menus ................................................................................. 2-9

2.5

Washing Sequence Modes............................................................ 2-10

2.5.1

Washing Modes ............................................................................... 2-10

2.5.2

Aspirating Positions ......................................................................... 2-11

2.6

Rinse Modes................................................................................... 2-11

Installation Procedure

3.1

Unpacking and Inspection .............................................................. 3-1

3.2

Unpacking Procedure...................................................................... 3-2

3.3

Power Requirements ....................................................................... 3-2

3.4

Installation Procedure ..................................................................... 3-3

3.4.1

Installing the Instrument..................................................................... 3-3

3.4.2

Connecting the Solution Tubes.......................................................... 3-3

3.4.3

Fitting and Connecting the Liquid Sensors (Optional) ....................... 3-4

3.4.4

Connecting the Barcode Reader (Optional)....................................... 3-5

3.4.5

Connecting the Printer (Optional) ...................................................... 3-5

3.4.6

Power Connections............................................................................ 3-5

Operating Instructions

4.1

Switching the Instrument On .......................................................... 4-1

4.2

Mode Selection Menu ...................................................................... 4-2

4.3

Priming Procedure........................................................................... 4-3

4.4

Operating Instructions .................................................................... 4-4

Procedure to Wash Individually Selected Strips ................................ 4-5

Instrument with Printer and Barcode Reader Options ....................... 4-6

Fill Verification.................................................................................... 4-7

Drip Mode Option (Cell Wash) ........................................................... 4-9

384 Well Manifold Option................................................................... 4-9

May 2003

Instructions for Use for Columbus Washer No. I 109 006 Rev No. 2.2

Содержание Columbus Washer



















































































Результаты поиска

Содержание Columbus Washer

Отзывы:

Похожие инструкции для Columbus Washer

Бренды по названию

Популярные бренды

tecan Columbus Washer, Инструкция по эксплуатации

Результаты поиска

Содержание Columbus Washer

Отзывы:

Похожие инструкции для Columbus Washer

Бренды по названию

Популярные бренды