tecan Columbus Washer Скачать руководство пользователя страница 31

Страница: 31 / 82

4. Operating Instructions

4.3 Priming

Procedure

Before the instrument can be used, all dispensing channels must be primed
with the required solution.

Ensure that the bottle of priming solution is always full at the beginning of
the priming procedure and check that the inlet filters in the liquid tubes are
clear.

Note:

Please ensure that the dispensing and aspiration pumps are not run for

longer than a few minutes without liquid or they will be damaged.

The priming procedure is performed using the following procedure:

Run XX yyyyyyyy
- + other yes

Prime Ch1
- + other yes

Prime Solution ?
exit yes

Waste Bottle OK?
exit yes

Prime ChX Y sec
Stop

Run XX yyyyyyyy
- + other yes

Priming Procedure

performed

Select required channel to be primed

Waste bottle empty

Instrument ready to wash microplate

Required solution in bottle and inlet
tube inserted into solution

Priming procedure being performed

Caution

Do not use the instrument to aspirate or dispense any acidic solutions as

this could damage the instrument

May 2003

Instructions for Use for Columbus Washer No. I 109 006 Rev No. 2.2

4-3

Содержание Columbus Washer



















































































Результаты поиска

Содержание Columbus Washer

Отзывы:

Похожие инструкции для Columbus Washer

Бренды по названию

Популярные бренды

tecan Columbus Washer, Инструкция по эксплуатации

Результаты поиска

Содержание Columbus Washer

Отзывы:

Похожие инструкции для Columbus Washer

Бренды по названию

Популярные бренды