tecan Columbus Washer Скачать руководство пользователя страница 72 | Manualshive

Страница: 72 / 82

background image

7. Maintenance and Cleaning

4. Switch off the instrument and disconnect the instrument from the mains

power supply.

5. Disconnect the instrument from any accessories that are used for example:

printer, computer and so forth. Accessories that should be shipped together
with the instrument have to be included in the disinfection procedure.

6. Carefully spray the disinfectant solution (or use a disposable soft tissue

paper towel soaked in the disinfectant) on all outer surfaces of the
instrument.

7. After a minimum contact time of 10 minutes, repeat step 6 of this procedure.

8. Wipe dry the outer surfaces of the instrument.

9. Pack the instrument and its accessories.

10. Disinfect your hands and clean them with a mild detergent.

11.

Complete a disinfection certificate and attach it to the outside of the
box so that it is clearly visible.

(See below for an example of the

disinfection certificate).

The following label MUST be completed and attached to the top of the package in
which the instrument is returned, before sending the instrument to the servicing
center for repair.

I declare that the instrument in this package has never been exposed to any
hazardous biological material or that it has been decontaminated or
disinfected to remove or inactivate any biological material which could be
dangerous to the service personnel.

Name:..................................................................................................................

Firm: ....................................................................................................................

Address: ..............................................................................................................

............................................................................................................................

............................................................................................................................

Country:...............................................................................................................

Signature:............................................................................................................

7-14

Instructions for Use for Columbus Washer No. I 109 006 Rev No. 2.2

May 2003

«
...
70
71
72
73
74
...
»

Содержание Columbus Washer



















































































Отзывы:

Нет отзывов

Похожие инструкции для Columbus Washer

Бренд: ABB Страницы: 11

Бренд: Harken Страницы: 4

Бренд: Landoll Страницы: 52

Бренд: Gason Страницы: 110

Бренд: Gainsborough Страницы: 2

Бренд: BACtrack Страницы: 16

Бренд: Dawn Страницы: 8

Бренд: BACtrack Страницы: 13

Бренд: Badgematic Страницы: 28

Бренд: BACtrack Страницы: 2

Бренд: MADRIX Страницы: 28

Бренд: BACTcontrol Страницы: 28

Бренд: Keiser Страницы: 82

Бренд: Keiser Страницы: 4

Бренд: Kamikaze Страницы: 112

Бренд: KAM Страницы: 2

Бренд: Pahlen Страницы: 20

Бренд: Paia Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды