manualshive.com logo in svg

TDK-Lambda GXE600 Series, Руководство по связи

Поделиться
Скачать
TDK-Lambda GXE600 Series Скачать руководство пользователя страница 78

COMMUNICATION MANUAL

GXE600 SERIES

TDK­Lambda

<Page>

78/79

Supplementary

1. Communication configuration switch

It is possible to set and check all communication configurations of the GXE series by use communication lines.

GXE series don't have display function of the communication configuration.

When disconnecting GXE from communication bus line due to changing system configuration, etc., you might miss the 

communication configuration of it. If the communication configuration switch is disabled(DIS) and you apply input to GXE, 

GXE start with default communication configuration.

!

To prevent electric shock, operate the switch after enough time has elapsed from input shutdown.

*Default Communication Configuration

Item

Default Setting

Slave ID

ID : 1

Baud Rate

19200 bps

Parity

Even parity

Stop bit

 1 bit

By connecting to GXE with one to one by use this communication configuration, you can confirm or change to communication 

configuration of GXE.

!

If the switch is disable(DIS) and plural GXEs connected to the bus, you cannot correct communication.

Step1: After sufficient time has elapsed since the input is cut off, switch the communication configuration switch 

to disable(DIS). Refer to the figure below for the location and direction of the switch.

Step2: Read the communication configuration related registers and check the setting contents.

Step3: Modify the register settings related to communication settings as necessary and update them.

Step4: After sufficient time has elapsed since the AC input was cut off, you switch the communication configuration switch 

to enable(EN).

*/A : For the option model with cover, slide the SW81 from the rectangle hole 

        at side surface by non conductive tweezers etc..


Communication  Configuration  Swtch (SW81)

ENABLE

DISABLE

Содержание GXE600 Series
















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды