TDK-Lambda GXE600 Series Скачать руководство пользователя страница 65

Страница: 65 / 79

COMMUNICATION MANUAL

GXE600 SERIES

TDKLambda

<Page>

65/79

Re gist e r Nam e

PF Count

Data Type

Starting Address

Qty

Non-volatile

Holding

PF signal output confirmation time limit setting

Yes

1) Register Details

This is the configuration register for PF (Power Fail) signal output confirmation time (delay time).

The setting value is specified by integer data [ms].

When the output is below the PF detection threshold for a time longer than the set time, the PF signal is output

When the output returns to the PF detection threshold or higher within the set time, the PF signal is not output.

The PF signal detection level is set in the PF threshold register.

The PF signal detection target is selected by the PF mode setting register.

Configuration data is retained even when input is cut off.

・Register setting value

Data Type

Max

Min

Factory setting

16 bit integer

100

*An exception response (Exception code: 0x03) is returned when writing values outside the range.

Unit

113

(0x0071)

確認時限

～

100 msec]

Vo / Io

閾値

信号

PF detection threshold

PF signal

Check time limit [0 ~ 100 ms]

Содержание GXE600 Series
















































































Результаты поиска

Содержание GXE600 Series

Отзывы:

Бренды по названию

Популярные бренды

TDK-Lambda GXE600 Series, Руководство по связи

Результаты поиска

Содержание GXE600 Series

Отзывы:

Бренды по названию

Популярные бренды