TDK-Lambda GXE600 Series Скачать руководство пользователя страница 57

Страница: 57 / 79

COMMUNICATION MANUAL

GXE600 SERIES

TDKLambda

<Page>

57/79

Re gist e r Nam e

Changing Time of OutputVoltage at steady state

Data Type

Starting Address

Qty

Non-volatile

Holding

Voltage slew rate at steady state setting

Yes

1) Register Details

This is the configuration register for slew rate when PV reference value is changed during steady state.

The PV slew rate (dv / dt) is specified as the time required for the PV reference value to change from 0% to 100%.

Please do one of the following methods to validate the setting value.

・ Re-input

・ From Remote Off to Remote On

Configuration data is retained even when input is cut off.

・Register setting value

Data Type

Max

Min

Factory setting

16 bit integer

10000

*An exception response (Exception code: 0x03) is returned when writing values outside the range.

This function is the setting of the reference value, and it does not necessarily operate as set up.

Depending on the load impedance, the output current may not follow the PV reference.

To change the PV value at startup, the slew rate setting of the [# 11 PV reference rise time] register is applied, not this

The value set here is the time required for a change of 0% ⇒ 100%

Actual changing time is equivalent to ΔPV reference value / rated value.

Example) PV reference value : 0.5 ⇒ 1.0 [Q10]、Register setting value : 1000 [ms]

Actual changing time = Register setting value x ΔPV reference value / Rated value

　　 = 1000 x (1.0 - 0.5) / 1.0 = 500 [ms]

Unit

109

(0x006D)

設定値

実際の遷移時間

t [msec]

PV [%]

100

Actual changing time

Setting value

t [ms]

Содержание GXE600 Series
















































































Результаты поиска

Содержание GXE600 Series

Отзывы:

Бренды по названию

Популярные бренды

TDK-Lambda GXE600 Series, Руководство по связи

Результаты поиска

Содержание GXE600 Series

Отзывы:

Бренды по названию

Популярные бренды