TDK-Lambda GXE600 Series Скачать руководство пользователя страница 61

Страница: 61 / 79

COMMUNICATION MANUAL

GXE600 SERIES

TDKLambda

<Page>

61/79

Re gist e r Nam e

PF Threshold

Data Type

Starting Address

Qty

Non-volatile

Holding

PF detection threshold setting

Yes

1) Register Details

This is the configuration register for detection threshold when outputting PF signal.

The PF detection threshold value is specified by signed 16-bit integer as "%" with PV reference value or CC reference

value as 100%.

The PF signal detection target is selected by the "PF mode setting register".

Configuration data is retained even when input is cut off.

・Register setting value

Data Type

Max

Min

Factory setting

Accuracy

16 bit integer

3.0%

*An exception response (Exception code: 0x03) is returned when writing values outside the range.

The PF detection threshold is compared with the detection target, and when the target falls below the threshold value, the

PF signal is output.

The detection target is selected by [# 14 PF mode] register setting and the target is output voltage or output current.

PF signal update cycle is every 1 ms.

The output display LED of the power supply unit turn off in synchronization with the PF signal output.

In order to prevent signal fluttering, it is possible to set the confirmation time limit by setting the [# 15 PF count] register.

Also, when a voltage is applied to the output terminal of the power supply from the outside, if the PF threshold is exceeded,

the PF signal will be canceled, but not in sleep mode.

For details, Refer to the instruction manual.

Unit

111

(0x006F)

Vo / Io

閾値

信号

消灯

点灯

LED

OFF

PF signal

PF detection

threshold

Содержание GXE600 Series
















































































Результаты поиска

Содержание GXE600 Series

Отзывы:

Бренды по названию

Популярные бренды

TDK-Lambda GXE600 Series, Руководство по связи

Результаты поиска

Содержание GXE600 Series

Отзывы:

Бренды по названию

Популярные бренды