Taiden hcs-8300 Скачать руководство пользователя страница 31

Страница: 31 / 255

Chapter 2 Congress main unit (CMU)

The congress main unit (CMU) forms the core of the

HCS-8300 Series Paperless Multimedia Congress

System, It provides power supply to contribution units

and serves as the key component to link up hardware

with application software. In stand-alone mode without

a PC, the CMU carries out basic management facilities;

Comprehensive

management facilities can be

implemented in PC-controlled mode.

The following devices can be controlled by the CMU:

discussion unit(chairman unit/delegate unit), voting unit,

Interpreter unit, video switch for automatic video

tracking, etc. By cascade connecting EMUs, HCS-8300

system can reach its maximum capacity: 378

simultaneous Interpreter units, 4096 discussion/voting

units and an infinite number of channel selectors.

The maximum system capacity is 378 Interpreter units,

4096 discussion/voting units and any number of

channel selectors.

Product types:

HCS-8300MAU/FS

Fully Digital Congress System Main Unit (discussion, voting, 64

CHs, 256x32 LCD, MIC. group outputs, AES/EBU digital

input/output, single-mode optical fiber interface, CobraNet

interface)

HCS-8300MAD/FS/20

Fully Digital Congress System Main Unit (discussion, voting, 64

CHs, 256x32 LCD, MIC. group outputs, AES/EBU digital

input/output, To Mixer interface, single-mode optical fiber

interface, Dante interface)

HCS-8300MB/20

Fully Digital Congress System Main Unit (discussion, voting, 64

CHs, 256x32 LCD, MIC. group outputs)

HCS-8300MB

Fully Digital Congress System Main Unit (discussion, voting, 64

CHs, 256x32 LCD, MIC. group outputs)

HCS-8300ME/FS

Fully Digital Congress System Extension Main Unit (with 2

single-mode optical fiber interfaces)

HCS-8300ME

Fully Digital Congress System Extension Main Unit

HCS-8300MES

Fully Digital Congress System Extension Unit

Содержание hcs-8300
































































































































































































































































Результаты поиска

Содержание hcs-8300

Отзывы:

Бренды по названию

Популярные бренды

Taiden hcs-8300, Инструкция по установке и эксплуатации

Результаты поиска

Содержание hcs-8300

Отзывы:

Бренды по названию

Популярные бренды