Taiden hcs-8300 Скачать руководство пользователя страница 105

Страница: 105 / 255

Push the IC-card into the slot on the right side of the

terminal, if sign-in was successful; the figure is shown

as below. If not, “Invalid IC-card” will be displayed on

the LCD. Please push IC-card again or contact

technical support. While automatically logout once the

card is taken out from the slot.



Automatic Sign-in

In automatic sign-in mode, when operator click the

“Start Sign-in” button or select “Start sign-in

automatically after start conference” on DCS software,

the multimedia signed in automatically.

In above sign-in mode, after sign-in, the main interface

of the multimedia terminal displayed “You have

signed-in”. Shown as the following figure:



PIN code sign-in

In PIN code sign-in status, the LCD will display as the

following figure:

Input PIN code through virtual keyboard to sign in. If

the PIN code is wrong, "Invalid PIN code" will be

displayed on the LCD.



Seat IC-card and PIN code sign-in

In seat IC card and PIN code sign-in status, the LCD

will display as in the following figure:

Either IC card sign-in or PIN code sign-in will work.



Finger Print Sign-in

HCS-8338A and HCS-8348A series new generation

multimedia congress terminal built in fingerprint

identification module, in finger print sign-in status, the

LCD will display as the following figure:

Please press finger on the scanner according the

prompting information. Collecting finger print for every

delegate should be finished before meeting started.

Delegate without finger print data in the database will

not sign in successfully.

Содержание hcs-8300
































































































































































































































































Результаты поиска

Содержание hcs-8300

Отзывы:

Бренды по названию

Популярные бренды

Taiden hcs-8300, Инструкция по установке и эксплуатации

Результаты поиска

Содержание hcs-8300

Отзывы:

Бренды по названию

Популярные бренды