Taiden hcs-8300 Скачать руководство пользователя страница 203

Страница: 203 / 255

190

6.8.3 Operation

6.8.3.1 System startup

After connection of the power supply to the touch panel,

press the power button at the right side of the touch

panel to start the touch panel. The start-up logo will be

displayed as shown in the following figure:

The HCS-8319 is connected to the server with a Cat.5

cable. If not connected to the server, the interface shows

“Did not connect DCS Server”. If connected to the server,

the venue layout will be displayed on the LCD.

6.8.3.2 Function operation

1.Service request and response

When a delegate requests a service, its seat will be

highlighted and the detailed information of its service

request will be displayed on the service request list.

The operator double clicks on the service request list and

a response dialog will prompt. Click the “Response”

button to reply to the request.

All service requests will be listed in the service response

list in order.

Содержание hcs-8300
































































































































































































































































Результаты поиска

Содержание hcs-8300

Отзывы:

Бренды по названию

Популярные бренды

Taiden hcs-8300, Инструкция по установке и эксплуатации

Результаты поиска

Содержание hcs-8300

Отзывы:

Бренды по названию

Популярные бренды