Taiden hcs-8300 Скачать руководство пользователя страница 192

Страница: 192 / 255

179

6.5 HCS-8302MX/FS

HCS-8302MX/FS - the General Controller for Booth

Combiners - has at most twenty-four fiber interfaces.

Cable connections do not need to be changed. In

cooperation with HCS-8300MX/FS, at most twenty-four

rooms can be merged and their booths can be shared.

6.5.1 Functions and instructions

Front panel of General Controller for Booth Combiners HCS-8302MX/FS

Rear panel of General Controller for Booth Combiners HCS-8302MX/FS

Figure 6.5.1 HCS-8302MX/FS General Controller for Booth Combiners

Figure 6.5.1:

1. “MENU” button

2. “EXIT” button

3. “POWER” indicator

4. “ACTIVE” indicator



Indicator flashes in normal working state.

5. Fiber interface status buttons

6. “NETWORK” indicator



Indicator flashes

when

the

mainboard

communicates with the front panel board.

7. “

→

” (right) button

8. F2



Reserve

9. F1



Reserve

10. “

←

” (left) button

11. Fiber interfaces (1-24, 24 routes)



Single-mode optical fiber, SC connector.

12. Mini USB interface



For connecting to PC.

Содержание hcs-8300
































































































































































































































































Результаты поиска

Содержание hcs-8300

Отзывы:

Бренды по названию

Популярные бренды

Taiden hcs-8300, Инструкция по установке и эксплуатации

Результаты поиска

Содержание hcs-8300

Отзывы:

Бренды по названию

Популярные бренды