Taiden hcs-8300 Скачать руководство пользователя страница 113

Страница: 113 / 255

100

C. Language

Select the operation language.

D. Brightness

Setup the brightness of the LCD screen.

16. Snapshot

Press “Home” and “YES” key at the same time to shot

screen at any time. The picture (*.jpg file) was saved in

the “snapshot” file and can be viewed through

multimedia function.

If delegate arrangement finished, the picture name is

delegate name_increment, for example: John_0001.

If without delegate arrangement, the picture name is

unit ID_increment, for example: 4019_0002.

）

VIP unit



Any delegate unit can be assigned as a VIP unit by

application software. At most 32 VIP units can be

assigned;



As long as the active microphone capacity is not

full, the microphone of the VIP unit can be

activated freely;



If the active microphone capacity is full, the

microphone of the VIP unit cannot be turned on

unless one of the active microphones is deactivated.

Содержание hcs-8300
































































































































































































































































Результаты поиска

Содержание hcs-8300

Отзывы:

Похожие инструкции для hcs-8300

Бренды по названию

Популярные бренды

Taiden hcs-8300, Инструкция по установке и эксплуатации

Результаты поиска

Содержание hcs-8300

Отзывы:

Похожие инструкции для hcs-8300

Бренды по названию

Популярные бренды