Taiden hcs-8300 Скачать руководство пользователя страница 188

Страница: 188 / 255

175

6.4.3 Configuration and operation

When installation and connection are finished, the

Booth

Combiner

HCS-8300MX/FS

should be

configured by the front panel menu operation or the

RoomBoothCombine software prior to the meeting.

The room combination and booth combination

functions are controlled by RoomBoothCombine

software.

A) Starting initialization

B) Initial interface on LCD

The LCD interface displays the room name and work

mode of the current Booth Combiner.



The first row shows the room number and the room

name;



The second row shows current work mode, the

HCS-8300MX/FS Booth Combiner has six work

modes:



Idle Mode:

no booth combination and no

room combination;



Master Mode:

the mode of master

conference room after room combination;



Slave Mode:

the mode of slave conference

room after room combination;



Tenant Mode:

the mode of conference

room which borrows booths in booth

combination;



Landlord Mode:

the mode of conference

room which lends booths in booth

combination;



Master Mode + Tenant Mode:

the mode of

master conference room which borrows

booths in room combination and booth

combination.

Note:



One HCS-8300MX/FS can lend its booths to

only one HCS-8300MX/FS, and not to several

HCS-8300MX/FS at the same time;



One HCS-8300MX/FS cannot borrow as well

as lend booths at the same time.

Содержание hcs-8300
































































































































































































































































Результаты поиска

Содержание hcs-8300

Отзывы:

Бренды по названию

Популярные бренды

Taiden hcs-8300, Инструкция по установке и эксплуатации

Результаты поиска

Содержание hcs-8300

Отзывы:

Бренды по названию

Популярные бренды