Tadano GR-130EX Скачать руководство пользователя страница 31

Страница: 31 / 152

Y-2

Adjusting Pressure (Hydraulic Pressure)

WY02-2090E

2.5 Remote control pilot valve

[NOTICE]

Oil temperature: 50 ± 5°C (122 ± 9°F) (Hydraulic oil: TADANO Hydraulic Oil LL)
Shift the control lever or switch while the engine is idling, then increase engine speed.

Item

(Mark)

Set pressure

Engine

speed

(min

-1

)

Check procedure

MPa

kgf/cm

psi

Pilot

pressure

(R) 2.9 or over 30 or over 427 or over

770

(IDL.)

1. Connect a pressure gauge to the pressure

check port (R).

2. Turn the PTO switch ON.
3. With the air conditioner OFF, check the

pressure by the pressure gauge.

(Note): Adjustment is not possible.

If the pressure is out of the set

pressure range, replace the valve.

(S) 3.9 or less 40 or less 570 or less

770

(IDL.)

1. Connect a pressure gauge to the pressure

check port (S).

2. Turn the PTO switch ON.
3. With the air conditioner ON and the

compressor ON, check the pressure by

the pressure gauge.

*1: Sequence valve (for actuator)
*2: Reducing valve (for pilot pressure and slewing brake release)

Содержание GR-130EX

























































































































































Результаты поиска

Содержание GR-130EX

Отзывы:

Похожие инструкции для GR-130EX

Бренды по названию

Популярные бренды

Tadano GR-130EX, Руководство по обслуживанию

Результаты поиска

Содержание GR-130EX

Отзывы:

Похожие инструкции для GR-130EX

Бренды по названию

Популярные бренды