Tadano GR-130EX Скачать руководство пользователя страница 36

Страница: 36 / 152

Y-4

Air Bleeding Procedure

WY05-5140E

Y-4 Air Bleeding Procedure
1. Hydraulic pump

[NOTICE]

Be sure that the following conditions are met before

starting the engine.

•

PTO

: OFF

•

Air conditioner : OFF

•

Oil cooler

: OFF

The following is also possible:

After performing step 3. under 1.1, perform step 2.

under 1.2. Start the engine, then turn ON the PTO,

and run-in the pump for 10 minutes.

1.1 Gear pump

1. Fill the hydraulic oil tank with the hydraulic oil.

2. With the engine stopped, loosen the air-bleed plug

(G1/4) on the suction flange of the variable piston
pump. After bleeding the suction side, tighten the
plug again.

3. Start the engine (with air conditioner and oil cooler

OFF and PTO OFF), and run it at idle
(approximately 770 min

-1

) for 1 minute to bleed

the circuit.

4. Start the engine, and run-in the pump for 10

minutes at idle.

1.2 Variable piston pump

1. Fill the hydraulic oil tank with the hydraulic oil. (If

the suction section is disassembled due to repair
or other reasons, bleed the suction side from the
air-bleed plug on the suction side as described
above.)

2. Bleed the pump case. Remove the air-bleed plug

(G3/8) on top of the pump.
Pour the hydraulic oil into this plug until the oil
overflows, then tighten the plug again.

3. Start the engine with the PTO ON, and run-in the

pump at idle for 5 minutes.

Содержание GR-130EX

























































































































































Результаты поиска

Содержание GR-130EX

Отзывы:

Похожие инструкции для GR-130EX

Бренды по названию

Популярные бренды

Tadano GR-130EX, Руководство по обслуживанию

Результаты поиска

Содержание GR-130EX

Отзывы:

Похожие инструкции для GR-130EX

Бренды по названию

Популярные бренды