Tadano GR-130EX Скачать руководство пользователя страница 32

Страница: 32 / 152

Y-2

Adjusting Pressure (Hydraulic Pressure)

WY02-2090E

2.6 Steering

[NOTICE]

Oil temperature: 50 ± 5°C (122 ± 9°F) (Hydraulic oil: TADANO Hydraulic Oil LL)
Shift the control lever or switch while the engine is idling, then increase engine speed.

Item

(Mark)

Set pressure

Engine

speed

(min

-1

)

Check procedure

MPa

kgf/cm

psi

Steering

(I)

18.6 ± 1.0 190 ± 10 2700 ± 140 2700

(MAX.)

1. Connect a pressure gauge to the pressure

check port (I).

2. Without jacking up, turn the steering to the

right side. Gently move the steering cylinders

to the end of the stroke.

3. In this state, set the engine speed to 2700

min

-1

and check the pressure by the pressure

gauge.

(Note): Adjustment is not possible.

If the pressure is out of the set pressure

range, replace the priority valve.

Содержание GR-130EX

























































































































































Результаты поиска

Содержание GR-130EX

Отзывы:

Похожие инструкции для GR-130EX

Бренды по названию

Популярные бренды

Tadano GR-130EX, Руководство по обслуживанию

Результаты поиска

Содержание GR-130EX

Отзывы:

Похожие инструкции для GR-130EX

Бренды по названию

Популярные бренды