Tadano GR-130EX Скачать руководство пользователя страница 62

Страница: 62 / 152

WY05-2492E

Y-8.

Operation Check (Crane Operation)

5. Warning

[NOTICE]

For the location of the buzzers, refer to "Z-10 Electric Parts Location Diagram (Upper), 1. Inside cab ".

6. Eco mode operation check

[NOTICE]

For the location of the switch, refer to “Z-10 Electric

Parts Location Diagram (Upper), 1. Inside cab”.

While the PTO is engaged, select the Eco mode 1

and Eco mode 2, and depress the accelerator
pedal fully. Then check that the maximum engine
speed lowers while the respective mode is
selected.

Eco mode

Max. engine speed (min

-1

)

OFF

Approx. 1700

Approx. 1400

Approx. 1200

Use the AML to select the Eco mode 1 or Eco mode

2. The maximum engine speeds above listed are for

reference.

Item

Warning

buzzer

Sound

Checking procedure

AML limit

Buzzer

(CN818)

Continuous beep

(low tone)

Buzzer sounds at 100% when main switch is ON and PTO

switch is ON. (Intermittent low tone sound occurs at 90%

and above.)

Two-blocking

warning

Buzzer

(CN817)

Continuous beep

(high-low tones)

Buzzer sounds when the two-blocking detection switch

contact of either the main or auxiliary winch is turned OFF

by winch hoisting up operation.

Outrigger

operation switch

detection

Buzzer

(CN815,

CN816)

Intermittent beep

(high tone)

Buzzer sounds when either the outrigger extend/retract or

jack slide selector switch has been left in any position

other than neutral for 10 seconds or more after operation

is completed.

△

345-804-54500

Содержание GR-130EX

























































































































































Результаты поиска

Содержание GR-130EX

Отзывы:

Похожие инструкции для GR-130EX

Бренды по названию

Популярные бренды

Tadano GR-130EX, Руководство по обслуживанию

Результаты поиска

Содержание GR-130EX

Отзывы:

Похожие инструкции для GR-130EX

Бренды по названию

Популярные бренды