Supermicro SuperServer SYS-240P-TNRT Скачать руководство пользователя страница 5

Страница: 5 / 123

Preface

Chapter 3 Maintenance and Component Installation

3.1 Powering Down the System ..............................................................................................26
3.2 Accessing the System ........................................................................................................27

Removing the Top Cover ...............................................................................................27

3.3 Static-Sensitive Devices .....................................................................................................28

Precautions .......................................................................................................................28

3.4 Processor and Heatsink Installation ...................................................................................29

3.5 Memory ...............................................................................................................................39

Memory Support ................................................................................................................39
Memory Installation Sequence ..........................................................................................39
General Memory Population Requirements ......................................................................39
DDR4 Memory Population Table .....................................................................................40

Memory Population Sequence for Half Memory Configuration

.....................................40

Memory Population Table with Full Memory Configuration

...........................................40

Intel® Optane™ PMem 200 Series Memory Population (Full Configuration)

...............40

DIMM Installation ..............................................................................................................42
DIMM Removal .................................................................................................................42

3.6 Motherboard Battery ...........................................................................................................43
3.7 Storage Drives ....................................................................................................................44

Checking the Temperature of an NVMe Drive ..................................................................44
Installing Drives .................................................................................................................44
Hot-Swap for NVMe Drives ...............................................................................................46
Installing M.2 Solid State Drives .......................................................................................47

Installing M.2 Drives ......................................................................................................47

3.8 System Cooling ..................................................................................................................48

Fans ..................................................................................................................................48
Air Shrouds .......................................................................................................................49

Содержание SuperServer SYS-240P-TNRT




























































































































Результаты поиска

Содержание SuperServer SYS-240P-TNRT

Отзывы:

Похожие инструкции для SuperServer SYS-240P-TNRT

Бренды по названию

Популярные бренды

Supermicro SuperServer SYS-240P-TNRT, Руководство пользователя

Результаты поиска

Содержание SuperServer SYS-240P-TNRT

Отзывы:

Похожие инструкции для SuperServer SYS-240P-TNRT

Бренды по названию

Популярные бренды