Supermicro SuperServer SYS-240P-TNRT Скачать руководство пользователя страница 36

Страница: 36 / 123

Chapter 3: Maintenance and Component Installation

PEEK Nut

Rotating Wire

Side View

Top View

Unlatched State

Removing the PHM from the CPU Socket

Before removing the PHM from the motherboard, first shut down the system and unplug the

AC power cord from all power supplies.

1. Use a t30-bit screwdriver to loosen the four peek nuts on the heatsink in the sequence

of A, B, C, and D.

PEEK Nut

2. Once the peek nuts have been loosened from the CPU socket, press the rotating wires

inward to unlatch the PHM from the socket as shown below.

3. Gently lift the PHM upward to remove it from the CPU socket.

Содержание SuperServer SYS-240P-TNRT




























































































































Результаты поиска

Содержание SuperServer SYS-240P-TNRT

Отзывы:

Похожие инструкции для SuperServer SYS-240P-TNRT

Бренды по названию

Популярные бренды

Supermicro SuperServer SYS-240P-TNRT, Руководство пользователя

Результаты поиска

Содержание SuperServer SYS-240P-TNRT

Отзывы:

Похожие инструкции для SuperServer SYS-240P-TNRT

Бренды по названию

Популярные бренды