Supermicro SuperServer SYS-240P-TNRT Скачать руководство пользователя страница 53 | Manualshive

Страница: 53 / 123

background image

53

Chapter 3: Maintenance and Component Installation

3.10 Power Supply

The system includes two hot-plug, 2000W power supply modules. These modules will

automatically sense and operate at an input voltage between 100v to 240v. Note that different
input voltages will result in different maximum power output levels.

In the event of a power module failure, the other power module will continue to power the
system on its own. Failed power supply modules can be replaced without powering-down the
system. Replacement modules can be ordered directly from Supermicro.

An amber light on the power supply is illuminated when the power is switched off. A green

light indicates that the power supply is operating.

Replacing the Power Supply

1. Unplug the AC power cord from the failed power supply module.

2. Push and hold the release tab on the back of the power supply.

3. Grasp the handle of the power supply and pull it out of its bay.

4. Push the new power supply module into the power bay until it clicks into the locked

position.

5. Plug the AC power cord back into the power supply module.

Figure 3-12. Installing a Power Supply Module

Handle

Tab

«
...
51
52
53
54
55
...
»

Содержание SuperServer SYS-240P-TNRT




























































































































Отзывы:

Нет отзывов

Похожие инструкции для SuperServer SYS-240P-TNRT

SX-2000A Series

Бренд: GDC Страницы: 185

Бренд: Axis Страницы: 10

Бренд: AXIOMTEK Страницы: 58

Бренд: ANTAIRA Страницы: 2

Бренд: MSI Страницы: 54

Бренд: IBM Страницы: 21

419452u - Servers System X3250 M2 Xeon...

Бренд: IBM Страницы: 84

Бренд: Atop Страницы: 2

PLATINUM 1500 IR M5

Бренд: MAXDATA Страницы: 44

ANTMINER S19 Pro

Бренд: BITMAIN Страницы: 17

Бренд: TRENDnet Страницы: 3

Бренд: DSP4YOU Страницы: 28

SuperWorkstation 5049A-TR

Бренд: Supermicro Страницы: 189

SuperStorageServer SSG-6119P-ACR12N4L

Бренд: Supermicro Страницы: 211

Бренд: AirLive Страницы: 106

Image Server 2000 V-2000

Бренд: 360 Systems Страницы: 137

Бренд: Raidon Страницы: 71

Бренд: ClearCube Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды