Supermicro SuperServer SYS-240P-TNRT Скачать руководство пользователя страница 38

Страница: 38 / 123

Chapter 3: Maintenance and Component Installation

Removing the Processor from the Processor Carrier Assembly

Once you have removed the processor carrier assembly from the PHM, you are ready to
remove the processor from the processor carrier by following the steps below.

1. Unlock the lever from its locked position and push it upwards to disengage the

processor from the processor carrier as shown below right.

Lever

Processor Carrier Assembly

2. Once the processor has been loosened from the carrier, carefully remove the processor

from the carrier.

Note:

Please handle the processor with care to avoid damaging it or its pins.

Содержание SuperServer SYS-240P-TNRT




























































































































Результаты поиска

Содержание SuperServer SYS-240P-TNRT

Отзывы:

Похожие инструкции для SuperServer SYS-240P-TNRT

Бренды по названию

Популярные бренды

Supermicro SuperServer SYS-240P-TNRT, Руководство пользователя

Результаты поиска

Содержание SuperServer SYS-240P-TNRT

Отзывы:

Похожие инструкции для SuperServer SYS-240P-TNRT

Бренды по названию

Популярные бренды