Supermicro SuperServer SYS-240P-TNRT Скачать руководство пользователя страница 122

Страница: 122 / 123

122

Appendix C: Chinese Safety Warnings

限用物質含有情況標示聲明書

設備名稱：伺服器

Server

型號（型式）：

218H-R20X12

(

系列型號

: ):

SYS-240P-TNRT , 218H-20, 218H-MP4

單元

Ｕ

nit

限用物質及其化學符號

鉛

Lead

(Pb)

汞

Mercury

(Hg)

鎘

Cadmium

(Cd)

六價鉻

Hexavalent

chromium

(Cr

)

多溴聯苯

Polybrominated

biphenyls

(PBB)

多溴二苯醚

Polybrominated

diphenyl ethers

(PBDE)

機殼

(Chassis)

○

機殼風扇

(Chassis Fan)

－

○

線材

(Cable)

○

主機板

(Motherboard)

－

○

電源供應器

(Power Supply)

－

○

硬碟

(HDD, M.2)

－

○

電源背板

(PDB)

－

○

附加卡

(Add-on Card)

－

○

備考

〝超出

0.1 wt %

〞及〝超出

0.01 wt %

〞係指限用物質之百分比含量超出百分比含量基準值。

備考

〝○〞係指該項限用物質之百分比含量未超出百分比含量基準值。備考

〝－〞係

指該項限用物質為排除項目。

Declaration of the Presence Condition of the Restricted Substances Marking

Equipment name

Type designation (Type)

Restricted substances and its chemical symbols

Note 1

：

“

xceeding 0.1 wt %” and “exceeding 0.01 wt %” indicate that the percentage content of the restricted substance

exceeds the

reference percentage value of presence condition.

Note 2

：

“

○

” indicates that t

he percentage content of the restricted substance does not exceed the percentage of reference value of presence.

Note 3

：

The “−” indicates that the restricted substance corresponds to the exemption.

Appendix C

BSMI Chinese Safety Warnings

Содержание SuperServer SYS-240P-TNRT




























































































































Результаты поиска

Содержание SuperServer SYS-240P-TNRT

Отзывы:

Похожие инструкции для SuperServer SYS-240P-TNRT

Бренды по названию

Популярные бренды

Supermicro SuperServer SYS-240P-TNRT, Руководство пользователя

Результаты поиска

Содержание SuperServer SYS-240P-TNRT

Отзывы:

Похожие инструкции для SuperServer SYS-240P-TNRT

Бренды по названию

Популярные бренды