Supermicro SuperServer SYS-240P-TNRT Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 123

background image

29

Chapter 3: Maintenance and Component Installation

3.4 Processor and Heatsink Installation

The processor (CPU) must first be attached to the processor carrier to form the processor

carrier assembly. This assembly gets attached to the heatsink to form the processor heatsink
module (PHM), which is then installed into the CPU socket. Before installing, be sure to
perform the steps below:

•

Please carefully follow the instructions given on ESD precautions.

•

After shutting down the system, unplug the AC power cords from all power supplies.

•

Check that the plastic protective cover is on the CPU socket and that none of the socket
pins are bent. If they are, contact your retailer.

•

When handling the processor, avoid touching or placing direct pressure on the LGA lands
(gold contacts). Improper installation or socket misalignment can cause serious damage
to the processor or the socket, and may require manufacturer repairs.

•

Thermal grease is pre-applied on new heatsinks. No additional thermal grease is needed.

•

Refer to the Supermicro website for updates on processor and memory support.

•

All graphics in this manual are for illustration only. Your components may look different.

«
...
27
28
29
30
31
...
»

Содержание SuperServer SYS-240P-TNRT




























































































































Отзывы:

Нет отзывов

Похожие инструкции для SuperServer SYS-240P-TNRT

Бренд: US Robotics Страницы: 156

Бренд: 7starlake Страницы: 32

Бренд: MSI Страницы: 54

4-Port USB 2.0 Device Server over IP...

Бренд: Quatech Страницы: 2

376227-B21 - ProLiant InfiniBand 4x Fabric Copper Switch

Бренд: HP Страницы: 169

SUPERSERVER 7045W-NTR+

Бренд: Supero Страницы: 146

PCS400R Pro:Centric

Бренд: LG Страницы: 57

Бренд: LG Страницы: 104

Pro:Centric PCS200S

Бренд: LG Страницы: 40

Бренд: LG Страницы: 6

PCS500R Pro:Centric

Бренд: LG Страницы: 70

Бренд: LG Страницы: 24

Centric PCS150R Pro

Бренд: LG Страницы: 35

Centric PCS200R Pro

Бренд: LG Страницы: 384

Бренд: Inventec Страницы: 129

Бренд: Polycom Страницы: 34

Бренд: Planet Страницы: 90

Бренд: Supermicro Страницы: 72

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды