Supermicro SuperServer SYS-240P-TNRT Скачать руководство пользователя страница 61 | Manualshive

Страница: 61 / 123

background image

61

Chapter 4: Motherboard Connections

NIC1/NIC2 (LAN1/LAN2)

The NIC (Network Interface Controller) LED connection for LAN port 1 is located on pins
11 and 12 of JF1, and LAN port 2 is on pins 9 and 10. These LAN ports support 10G LAN
Ethernet connections. Attach the NIC LED cables here to display network activity. Refer to

the table below for pin definitions.

HDD LED

The HDD LED connection is located on pins 13 and 14 of JF1. Attach a cable to pins 13 and

14 to show hard drive activity status. Refer to the table below for pin definitions.

HDD LED

Pin Definitions (JF1)

Pins

Definition

13

3.3V Stdby

14

HDD Active

LAN1/LAN2 LED

Pin Definitions (JF1)

Pins

Definition

9

NIC 2 Activity LED

11

NIC 1 Activity LED

Power LED

The Power LED connection is located on pins 15 and 16 of JF1. Refer to the table below

for pin definitions.

Power LED

Pin Definitions (JF1)

Pins

Definition

15

3.3V

16

PWR LED

NMI Button

The non-maskable interrupt (NMI) button header is located on pins 19 and 20 of JF1. Refer

to the table below for pin definitions.

NMI Button

Pin Definitions (JF1)

Pins

Definition

19

Control

20

Ground

«
...
59
60
61
62
63
...
»

Содержание SuperServer SYS-240P-TNRT




























































































































Отзывы:

Нет отзывов

Похожие инструкции для SuperServer SYS-240P-TNRT

imagePRESS Server G200

Бренд: Canon Страницы: 82

Бренд: Canon Страницы: 88

Бренд: AIC Страницы: 52

Бренд: ACTi Страницы: 15

Бренд: TP-Link Страницы: 16

Netfinity 3500 Series

Бренд: IBM Страницы: 152

Бренд: Belkin Страницы: 8

Бренд: Dell Страницы: 396

Бренд: Dell Страницы: 180

EqualLogic PS6010

Бренд: Dell Страницы: 57

PowerVault 700N

Бренд: Dell Страницы: 29

Бренд: Dell Страницы: 133

WPS870G - Wireless Print Server

Бренд: Motorola Страницы: 115

Бренд: TYAN Страницы: 87

Бренд: GRASS VALLEY Страницы: 2

Бренд: Atrust Страницы: 21

Бренд: ATON Страницы: 2

ABLELink SW2001

Бренд: Atop Страницы: 51

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды