Supermicro SuperServer SYS-240P-TNRT Скачать руководство пользователя страница 79

Страница: 79 / 123

Chapter 6: Optional Components

Enabling NVMe RAID

RAID for NVMe SSDs must be enabled through the UEFI BIOS.

1. Install the patch as described in the Restrictions and Requirements section on a

previous page.

2. Reboot the server.

3. Press [DEL] key to enter BIOS.

4. Switch to

Advanced > Chipset Configuration > North Bridge > IIO Configuration >

Intel® VMD Technology > CPU3 & CPU4

Enable

the VMD according to the following rules.

•

For U.2 NVMe, enable all the sub-items under each PStack, based on the your model
server:

•

For M.2 NVMe or NVMe AIC, enable the VMD according to which AOC card/slot it used.

Examples for some U.2 configurations follow.

Press [F4] to save the configuration and reboot the system.

7. Press [DEL] to enter BIOS.

8. Switch to

Advanced > Intel(R) Virtual RAID on CPU > All Intel VMD Controllers >

Create RAID Volume

9. Set

Name

10. Set

RAID Level

11. If cross-controller RAID is required, select

Enable RAID spanned over VMD Controller

as shown in Figure 6-??.

12.

Select specific disks for RAID with an [X].

•

RAID0: Select at least two [2 - 24] disks

•

RAID1: Select only two disks

•

RAID5: Select at least three [3 - 24] disks

•

RAID10: Select only four disks

Содержание SuperServer SYS-240P-TNRT




























































































































Результаты поиска

Содержание SuperServer SYS-240P-TNRT

Отзывы:

Похожие инструкции для SuperServer SYS-240P-TNRT

Бренды по названию

Популярные бренды

Supermicro SuperServer SYS-240P-TNRT, Руководство пользователя

Результаты поиска

Содержание SuperServer SYS-240P-TNRT

Отзывы:

Похожие инструкции для SuperServer SYS-240P-TNRT

Бренды по названию

Популярные бренды