Supermicro SuperServer SYS-240P-TNRT Скачать руководство пользователя страница 56 | Manualshive

Страница: 56 / 123

background image

56

Chapter 4: Motherboard Connections

Chapter 4

Motherboard Connections

This section describes the connections on the motherboard and provides pinout definitions.
Note that depending on how the system is configured, not all connections are required. The

LEDs on the motherboard are also described here. A motherboard layout indicating component
locations may be found in

. More detail can be found in the

Motherboard Manual

Please review the Safety Precautions in

before installing or removing components.

4.1 Power Connections

Two power connections supply the motherboard and several more supply for onboard devices.

Main Power Connections

Two Power Delivery I

2

C1/2 Boards (PDB), located at PSU1 and PSU2, are used to provide

main power to your system.

Important:

To provide adequate power to your system, be sure to connect the Power Delivery

Boards (PSU1/2) and all 8-pin PWR connectors (BP_PWR1/2/3 & GPU_PWR1/2/3/4) to the
power supply. Failure to do so may void the manufacturer warranty on your power supply
and motherboard.

Backplane Power Connectors & GPU Power Connectors

In addition to the main power headers, three 8-pin power connectors (BP_PWR1/2/3) are
used for backplane devices. Another four 8-pin power connectors (GPU_PWR1/2/3/4) are for

GPU device use. These 8-pin power connectors meet the ATX SSI EPS 12V specification

and must be connected to your power supply to provide adequate power to your system.

12V 8-pin Power

Pin Definitions

Pin#

Definition

1 - 4 Ground
5 - 8 +12V

PDB Cable Connectors for CPU3/CPU4

Two PDB (Power Delivery Board) cable connectors for CPU3 and CPU4 are located at J26
and J47. J47 is used for CPU3, and J26 is for CPU4. See the layout below for the locations
for J47 and J26.

Power Connectors for PCIe 3.0 x16 HIO Slots (J5/J6)

Two 6-pin power connectors used for PCIe 3.0 x16 High_Speed (HIO) slots are located at J5/
J6. J5 is used for the left side PCIe 3.0 x16 slot (P1_HIO_L1PCIE), while J6 is for the right
side PCIe 3.0 x16 slot (P2_HIO_R1PCIE). See the layout below for the locations for J5 and J6.

«
...
54
55
56
57
58
...
»

Содержание SuperServer SYS-240P-TNRT




























































































































Отзывы:

Нет отзывов

Похожие инструкции для SuperServer SYS-240P-TNRT

Бренд: IBM Страницы: 106

Бренд: IBM Страницы: 200

Бренд: NEC Страницы: 128

SUPERSERVER 6035B-8R+

Бренд: Supero Страницы: 110

Бренд: Jatheon Страницы: 52

Бренд: Qeedji Страницы: 58

Бренд: Supermicro Страницы: 62

E7210 Master-FARM

Бренд: MSI Страницы: 34

Бренд: Siemens Страницы: 48

SINUMERIK 840Di sl/840D sl

Бренд: Siemens Страницы: 250

Бренд: Advantech Страницы: 76

Бренд: Advantech Страницы: 92

Бренд: Dataton Страницы: 11

206m - eServer xSeries - 8485

Бренд: IBM Страницы: 110

Бренд: IBM Страницы: 268

Бренд: Advantech Страницы: 100

Бренд: Red Hat Страницы: 6

Бренд: Lantronix Страницы: 223

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды