Supermicro SuperServer SYS-240P-TNRT Скачать руководство пользователя страница 55

Страница: 55 / 123

Chapter 3: Maintenance and Component Installation

3.12 BMC

The BMC can be reset using the button on the front control panel or on the chassis rear.

•

Reset—Press and hold the button. After six seconds, the LED blinks at 2 Hz. The BMC
resets and the reset duration is ~250 ms. Then the BMC starts to boot.

•

Restore factory default configuration—Hold the button for twelve seconds. The LED blinks
at 4 Hz while defaults are configured.

•

Firmware update—the UID LED blinks at 10Hz during a firmware update.

BMC Reset Options

Event

LED (Green)

Reset

Blinks at 2 Hz

Restore

Defaults

Blinks at 4 Hz

Update

Blinks at 10 Hz

Содержание SuperServer SYS-240P-TNRT




























































































































Результаты поиска

Содержание SuperServer SYS-240P-TNRT

Отзывы:

Похожие инструкции для SuperServer SYS-240P-TNRT

Бренды по названию

Популярные бренды

Supermicro SuperServer SYS-240P-TNRT, Руководство пользователя

Результаты поиска

Содержание SuperServer SYS-240P-TNRT

Отзывы:

Похожие инструкции для SuperServer SYS-240P-TNRT

Бренды по названию

Популярные бренды