Supermicro SuperServer SYS-240P-TNRT Скачать руководство пользователя страница 39

Страница: 39 / 123

Chapter 3: Maintenance and Component Installation

3.5 Memory

Memory Support

The -P has 48 DIMM slots to support up to 12TB 3DS ECC DDR4-3200:RDIMM/
LRDIMM or 18TB Intel® Optane™ DDR4-2666:DCPMM, RDIMM/LRDIMM//DCPMM. For
validated memory, use our

Product Resources page

Check the Supermicro website for

possible updates to memory support.

Memory Installation Sequence

Memory for this motherboard is populated using the "Fill First" method. The DIMM slots with

blue release tabs are considered the first DIMM of their channel and those with white release

tabs are the second of the channel. When installing memory modules, be sure to populate

the memory slots with the blue release tabs first and then populate the those with the white

release tabs.

General Memory Population Requirements

1. Be sure to use the memory modules of the same type and speed on the motherboard.

Mixing of memory modules of different types and speeds is not allowed.

2. Using unbalanced memory topology such as populating two DIMMs in one channel while

populating one DIMM in another channel will result in reduced memory performance.

3. Populating memory slots with a pair of DIMM modules of the same type and size will

result in interleaved memory, which will improve memory performance.

DDR4 Memory Support

Type

Ranks Per DIMM

Data Width

DIMM Capacity (GB)

Speed (MT/s); Voltage (V); Slots Per Channel (SPC)

and DIMMs Per Channel (DPC)

1DPC (1-DIMM

Per Channel)

2DPC (2-DIMM

Per Channel)

8Gb

16Gb

1.2 V

RDIMM

SRx8

8GB

16GB

3200

SRx4

16GB

32GB

DRx8

16GB

32GB

DRx4

32GB

64GB

RDIMM-3Ds

(4R/8R) x4

2H-64GB

4H-128GB

2H-128GB

4H-256GB

LRDIMM

QRx4

64GB

128GB

3200

LRDIMM-3Ds

(4R/8R) x4

4H-128GB

2H-128GB

4H-256GB

3200

Содержание SuperServer SYS-240P-TNRT




























































































































Результаты поиска

Содержание SuperServer SYS-240P-TNRT

Отзывы:

Похожие инструкции для SuperServer SYS-240P-TNRT

Бренды по названию

Популярные бренды

Supermicro SuperServer SYS-240P-TNRT, Руководство пользователя

Результаты поиска

Содержание SuperServer SYS-240P-TNRT

Отзывы:

Похожие инструкции для SuperServer SYS-240P-TNRT

Бренды по названию

Популярные бренды