Supermicro SuperServer SYS-240P-TNRT Скачать руководство пользователя страница 26

Страница: 26 / 123

Chapter 3: Maintenance and Component Installation

Chapter 3

Maintenance and Component Installation

This chapter provides instructions on installing and replacing main system components. To

prevent compatibility issues, only use components that match the specifications and/or part

numbers given.

Installation or replacement of most components require that power first be removed from the

system. Please follow the procedures given in each section.

3.1 Powering Down the System

Use the following procedure to ensure that power has been removed from the system. This
step is necessary when removing or installing non hot-swap components.

1. Use the operating system to power down the system.

2. After the system has completely shut down, disconnect the AC power cord(s) from the

power strip or outlet and remove the AC power cords from all power supply modules.

3. Disconnect the power cord(s) from the power supply module(s).

4. When performing service on non hot-swap components, remove the system from the

rack and place it on a bench or desk. Do not service with the system extended from the

rack.

Содержание SuperServer SYS-240P-TNRT




























































































































Результаты поиска

Содержание SuperServer SYS-240P-TNRT

Отзывы:

Похожие инструкции для SuperServer SYS-240P-TNRT

Бренды по названию

Популярные бренды

Supermicro SuperServer SYS-240P-TNRT, Руководство пользователя

Результаты поиска

Содержание SuperServer SYS-240P-TNRT

Отзывы:

Похожие инструкции для SuperServer SYS-240P-TNRT

Бренды по названию

Популярные бренды