STARPLUS STSe Key System Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 94

background image

1-4

Key Service Unit

Chapter 1 - Introduction

STARPLUS STSe - Installation Manual

August 2005

Software Upgrades

Future software enhancements and upgrades are easily retrofitted and installed in the system.
This will in most cases, provide backward compatibility with existing Starplus hardware, further
reducing the cost to upgrade or add features to an installed system.

Key Service Unit

This diagram illustrates the basic layout of both KSU cabinets, the card slots for the extension
boards, and the locations of the Champ connectors.

Basic Cabinet

The Basic Key Set Unit (BKSU) has mounting holes so that it can be mounted on the wall. The
Main Board Unit (MBU) contains the main CPU – MC68LC302, Memory – the memory size is
1 Mbyte (4Mbit x 2), Data is 512 Kbytes (1 Mbit x 4), and all other system-operating type circuitry
to support the maximum configuration of 28 CO lines and 50 stations.

A power supply board is also installed to provide enough power to support all CO lines, stations,
and daughter board options. The BKSU has an external power switch to turn power on/off to
the BKSU and EKSU.

50-pin amphenol connectors are located on the side of the BKSU to provide the interface for the
Station and CO boards.

Basic
SLIB2

DTIB
or SLIB

LCOB,
PRI, or

T1IB, PRI,

or VMIB

EKSU

BKSU

CO Champ
(Male)

Sta Champ
(Female)

CO Champ
(Male)

Sta Champ
(Female)

LCOB

or T1IB

LCOB
or T1IB

DTIB
or SLIB

S

lot

2

S

lot

3

S

lot

4

S

lot

5

S

lot

6

S

lot

7

S

lot

8

S

lot

9

S

lot

10

S

lot

11

S

lot

12

S

lot

13

T1IB

«
...
14
15
16
17
18
...
»

Содержание STSe Key System































































































Отзывы:

Нет отзывов

Похожие инструкции для STSe Key System

Бренд: Nelson Страницы: 12

Бренд: Waters Страницы: 21

Бренд: Teac Страницы: 3

Бренд: Olympia Страницы: 28

Бренд: Akura Страницы: 11

Бренд: switel Страницы: 93

Бренд: Uniden Страницы: 52

DECT1725 Series

Бренд: Uniden Страницы: 44

Бренд: Northland Страницы: 7

Бренд: Grandstream Networks Страницы: 40

Бренд: Radio Shack Страницы: 32

Бренд: Bittel Страницы: 6

CS2111 - 2.4 GHz Cordless Phone

Бренд: VTech Страницы: 54

DCT70585 Series

Бренд: Uniden Страницы: 76

AUDIO SYSTEM CONTROLLER SC-1

Бренд: Wisdom Страницы: 52

Бренд: GE Страницы: 2

Бренд: LG Страницы: 29

Бренд: LG Страницы: 71

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды