STARPLUS STSe Key System Скачать руководство пользователя страница 56

Страница: 56 / 94

3-28

Station/CO Wiring

Chapter 3 - Installation

STARPLUS STSe - Installation Manual

August 2005

Station/CO Wiring

Digital & Single Line Wiring

Digital Stations

Station port numbers are set by the location of the port on the Station Champ connector.

Station ports are numbered consecutively from 100 to 149.

The first 8 ports are reserved for the built-in DTIB ports, which are always 100-107.

If an optional DTIB board is installed in the first DTIB/SLIB slot (slot 3), its digital port
numbers will be 108-115.

If two DTIBs are installed in the first two DTIB/SLIB slots (slots 3 & 4), the digital ports will be
numbered 100-107 and 108-123.

Single Line Stations

If an optional SLIB is installed in the first DTIB/SLIB slot (slot 3), the single line ports will be
numbered 108-111.

Ports 148 and 149 are always for the two built-in single line ports.

Care must be taken when wiring stations, to ensure that digital keysets are only wired to digital
ports and single line phones are wired to single line ports.

The station numbers align with the slots as shown in the Station Champ Connector Table on

page 3-29

only if slots are used in a sequential manner from right to left.

Refer to the two examples of slot connections and the respective amphenol wiring / station
numbers on

page 3-31

to better understand the relationships.

CO Champ Connectors

CO line numbers align with the slots as shown in the CO Champ Connectors Table on

page 3-30

only if slots are used in a sequential manner from right to left.

Refer to the two examples of slot connections and the respective amphenol wiring / station
numbers on

page 3-31

to better understand the relationships.

Содержание STSe Key System































































































Результаты поиска

Содержание STSe Key System

Отзывы:

Похожие инструкции для STSe Key System

Бренды по названию

Популярные бренды

STARPLUS STSe Key System, Руководство по установке

Результаты поиска

Содержание STSe Key System

Отзывы:

Похожие инструкции для STSe Key System

Бренды по названию

Популярные бренды