STARPLUS STSe Key System Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 94

background image

KSU Mounting

3-5

Chapter 3 - Installation

STARPLUS STSe - Installation Manual

August 2005

KSU Mounting

The

STARPLUS

STSe

System consists of a Basic Key Service Unit (BKSU) cabinet. When additional

CO lines and stations are needed, the Expansion Key Service Unit (EKSU) cabinet must be
mounted above the BKSU. Both units have been designed to be compact and lightweight for
easy handling during installation.

Basic Cabinet

The BKSU consists of a plastic frame and cover designed for wall mounting. The KSU must NOT
be mounted on a masonry or dry-wall surface; a wooden backboard is required.

A mounting template is included with the BKSU. This template can be used to drill pilot holes
for mounting screws. Note that the template provides screw hole locations for the BKSU and
EKSU. The BKSU is mounted with three #10 or larger, 1½ inch or longer screws.

1. Drill pilot holes in the locations marked.

2. Insert the screws and tighten, leaving about ½ inch exposed.

KSU Template

«
...
31
32
33
34
35
...
»

Содержание STSe Key System































































































Отзывы:

Нет отзывов

Похожие инструкции для STSe Key System

Бренд: Jacob Jensen Страницы: 32

Бренд: Panasonic Страницы: 6

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 2

T-Mobile KX-HDV130

Бренд: Panasonic Страницы: 116

Бренд: Panasonic Страницы: 214

Бренд: Panasonic Страницы: 472

T-Mobile KX-HDV130

Бренд: Panasonic Страницы: 2

Бренд: Fanstel Страницы: 22

Бренд: Daewoo Страницы: 13

Бренд: Valcom Страницы: 1

Бренд: Valcom Страницы: 13

Бренд: Power Dynamics Страницы: 22

Бренд: Scanntronik Mugrauer Страницы: 45

Бренд: Lightspeed Страницы: 31

IntelliGate A150

Бренд: Aastra Страницы: 85

Бренд: Marmitek Страницы: 27

Бренд: Vortex Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды